Issues related to USB, after upgrade.

Discussion in general that pertains to Sabayon Linux - Must Pertain to Sabayon Linux

Moderator: Moderators

Post Reply
User avatar
albfneto
Sagely Hen
Posts: 1911
Joined: Fri Nov 16, 2007 1:15
Location: Ribeirão Preto City, São Paulo State, Brazil
Contact:

Issues related to USB, after upgrade.

Post by albfneto » Fri Jan 11, 2019 22:33

Resume of the problems: after upgrade, Sabayon no more found or configure in a good manner, some USB ports, hubs and devices...


Prior to the upgrades, the system was working good.

In one of my Sabayon installations.
after complete upgrade, including the new systemd version.

1. Some issues, problems, related to the USB ports or devices recognizing....

at first, the initial screen plymount, no more appears. Instead of this, only a verbose mode booting, in that,a fast message "plymout not open"...

also, in these verbose messages, issues, errors concerning some USB ports not more recognizing....

however, the boot is very fast and the SDDM Login appears (Is a Sabayon KDE), session opened, but some USB requiring devices no more working properly, examples:

my mouse moves (the cursor) auto up and down. Example, whern i move the cursor up, it moves down...

my USB printer (an HP 2050) no more print anything...

Using a command:

Code: Select all

# dmesg | grep -i USB


I seen the same USB errors that appears in the boot (see 1.) I used kwrite to write these errors (text saved in another working sabayon installation)

the errors are type as these:

Code: Select all

[    4.236292] usb 3-2: Product: USB2.0 Hub
[    4.262170] usb usb9: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 4.18
[    4.262172] usb usb9: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    4.262173] usb usb9: Product: OHCI PCI host controller
[    4.262174] usb usb9: Manufacturer: Linux 4.18.0-sabayon ohci_hcd
[    4.262175] usb usb9: SerialNumber: 0000:00:16.0
[    4.345135] usb 1-1: device descriptor read/64, error -71
[    4.543119] usb 6-5: new low-speed USB device number 2 using ohci-pci
[    4.624087] usb 1-1: device descriptor read/64, error -71
[    4.706137] usb 6-5: New USB device found, idVendor=1bcf, idProduct=0005, bcdDevice= 0.14
[    4.706139] usb 6-5: New USB device strings: Mfr=0, Product=2, SerialNumber=0
[    4.706141] usb 6-5: Product: USB Optical Mouse
[    4.721868] input: USB Optical Mouse as /devices/pci0000:00/0000:00:12.0/usb6/6-5/6-5:1.0/0003:1BCF:0005.0001/input/input3
[    4.721970] hid-generic 0003:1BCF:0005.0001: input,hidraw0: USB HID v1.10 Mouse [USB Optical Mouse] on usb-0000:00:12.0-5/input0
[    4.904017] usb 1-1: new full-speed USB device number 3 using xhci_hcd
[    5.047118] usb 3-2.4: new high-speed USB device number 4 using ehci-pci
[    5.081241] usb 1-1: device descriptor read/64, error -71
[    5.126775] usb 3-2.4: New USB device found, idVendor=05e3, idProduct=0608, bcdDevice=77.61
[    5.126777] usb 3-2.4: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[    5.126778] usb 3-2.4: Product: USB2.0 Hub
[    5.360240] usb 1-1: device descriptor read/64, error -71
[    5.463170] usb usb1-port1: attempt power cycle
[    6.155102] usb 1-1: new full-speed USB device number 4 using xhci_hcd
[    6.157642] usb 1-1: Device not responding to setup address.
[    6.369610] usb 1-1: Device not responding to setup address.
[    6.575117] usb 1-1: device not accepting address 4, error -71
[    6.753120] usb 1-1: new full-speed USB device number 5 using xhci_hcd
[    6.755663] usb 1-1: Device not responding to setup address.
[    6.961621] usb 1-1: Device not responding to setup address.
[    7.167114] usb 1-1: device not accepting address 5, error -71
[    7.167844] usb usb1-port1: unable to enumerate USB device
[ 1666.042595] usb 6-5: USB disconnect, device number 2
[ 1666.638572] usb 6-5: new low-speed USB device number 3 using ohci-pci
[ 1666.801585] usb 6-5: New USB device found, idVendor=1bcf, idProduct=0005, bcdDevice= 0.14
[ 1666.801588] usb 6-5: New USB device strings: Mfr=0, Product=2, SerialNumber=0
[ 1666.801589] usb 6-5: Product: USB Optical Mouse
[ 1666.812033] input: USB Optical Mouse as /devices/pci0000:00/0000:00:12.0/usb6/6-5/6-5:1.0/0003:1BCF:0005.0002/input/input15
[ 1666.812208] hid-generic 0003:1BCF:0005.0002: input,hidraw0: USB HID v1.10 Mouse [USB Optical Mouse] on usb-0000:00:12.0-5/input0
[ 1667.108439] usb 6-5: USB disconnect, device number 3
[ 1667.550468] usb 6-5: new low-speed USB device number 4 using ohci-pci
[ 1667.713594] usb 6-5: New USB device found, idVendor=1bcf, idProduct=0005, bcdDevice= 0.14
[ 1667.713597] usb 6-5: New USB device strings: Mfr=0, Product=2, SerialNumber=0
[ 1667.713599] usb 6-5: Product: USB Optical Mouse
complete output of the comand "dmesg | grep USB" is here:

http://dpaste.com/0B219SS
ALBERTO FEDERMAN NETO
albfneto
[email protected]
Favorite Distros: Sabayon, Gentoo, Mageia and OpenSUSE

User avatar
albfneto
Sagely Hen
Posts: 1911
Joined: Fri Nov 16, 2007 1:15
Location: Ribeirão Preto City, São Paulo State, Brazil
Contact:

Re: Issues related to USB, after upgrade.

Post by albfneto » Wed Jan 16, 2019 19:42

I'm searching in the internet and seems that the problem is in UDEV, example in libudev.
seems that coldplug not working or not found
ALBERTO FEDERMAN NETO
albfneto
[email protected]
Favorite Distros: Sabayon, Gentoo, Mageia and OpenSUSE

Post Reply