very very slow boot after equo world [Solved]

[chickenhawk]

Sabayon 3.5 kernel 2.6.26, bootup and shutdown very very slow after running equo world. Can't figure out on my own, please help. Here's dmesg

dmesg
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Linux version 2.6.26-sabayon (root@sabayon) (gcc version 4.2.3 (Gentoo 4.2.3 p1.0)) #1 SMP Sat Aug 9 12:00:55 UTC 2008
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
[ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000001ff77000 (usable)
[ 0.000000] BIOS-e820: 000000001ff77000 - 000000001ff79000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000001ff79000 - 0000000020000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee10000 (reserved)
[ 0.000000] BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] 0MB HIGHMEM available.
[ 0.000000] 511MB LOWMEM available.
[ 0.000000] found SMP MP-table at [c00fe710] 000fe710
[ 0.000000] Entering add_active_range(0, 0, 130935) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 130935
[ 0.000000] HighMem 130935 -> 130935
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 130935
[ 0.000000] On node 0 totalpages: 130935
[ 0.000000] DMA zone: 36 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4060 pages, LIFO batch:0
[ 0.000000] Normal zone: 1115 pages used for memmap
[ 0.000000] Normal zone: 125724 pages, LIFO batch:31
[ 0.000000] HighMem zone: 0 pages used for memmap
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] DMI 2.3 present.
[ 0.000000] ACPI: RSDP 000FD560, 0014 (r0 DELL )
[ 0.000000] ACPI: RSDT 000FD574, 0034 (r1 DELL GX240 8 ASL 61)
[ 0.000000] ACPI: FACP 000FD5A8, 0074 (r1 DELL GX240 8 ASL 61)
[ 0.000000] ACPI: DSDT FFFE3C22, 2393 (r1 DELL dt_ex 1000 MSFT 100000D)
[ 0.000000] ACPI: FACS 1FF77000, 0040
[ 0.000000] ACPI: SSDT FFFE5FB5, 00A7 (r1 DELL st_ex 1000 MSFT 100000D)
[ 0.000000] ACPI: APIC 000FD61C, 005C (r1 DELL GX240 8 ASL 61)
[ 0.000000] ACPI: BOOT 000FD678, 0028 (r1 DELL GX240 8 ASL 61)
[ 0.000000] ACPI: PM-Timer IO Port: 0x808
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] disabled)
[ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at 30000000 (gap: 20000000:dec00000)
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000
[ 0.000000] PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
[ 0.000000] SMP: Allowing 2 CPUs, 1 hotplug CPUs
[ 0.000000] PERCPU: Allocating 41256 bytes of per cpu data
[ 0.000000] NR_CPUS: 64, nr_cpu_ids: 2
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 129784
[ 0.000000] Kernel command line: root=/dev/ram0 ramdisk=8192 real_root=/dev/VolGroup00/LogVol00 dolvm quiet init=/linuxrc splash=silent,theme:sabayon vga=791 CONSOLE=/dev/tty1 resume=swap:/dev/mapper/VolGroup00-LogVol01
[ 0.000000] mapped APIC to ffffb000 (fee00000)
[ 0.000000] mapped IOAPIC to ffffa000 (fec00000)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 2048 (order: 11, 8192 bytes)
[ 0.000000] Detected 1695.052 MHz processor.
[ 0.000999] Console: colour dummy device 80x25
[ 0.000999] console [tty0] enabled
[ 0.000999] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000999] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000999] Memory: 502336k/523740k available (7395k kernel code, 20868k reserved, 3088k data, 552k init, 0k highmem)
[ 0.000999] virtual kernel memory layout:
[ 0.000999] fixmap : 0xffc74000 - 0xfffff000 (3628 kB)
[ 0.000999] pkmap : 0xff400000 - 0xff800000 (4096 kB)
[ 0.000999] vmalloc : 0xe0800000 - 0xff3fe000 ( 491 MB)
[ 0.000999] lowmem : 0xc0000000 - 0xdff77000 ( 511 MB)
[ 0.000999] .init : 0xc0b4b000 - 0xc0bd5000 ( 552 kB)
[ 0.000999] .data : 0xc0838cd2 - 0xc0b3cd90 (3088 kB)
[ 0.000999] .text : 0xc0100000 - 0xc0838cd2 (7395 kB)
[ 0.000999] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.000999] CPA: page pool initialized 1 of 1 pages preallocated
[ 0.000999] SLUB: Genslabs=12, HWalign=128, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.061015] Calibrating delay using timer specific routine.. 3393.04 BogoMIPS (lpj=1696524)
[ 0.061063] Mount-cache hash table entries: 512
[ 0.061378] Initializing cgroup subsys ns
[ 0.061387] Initializing cgroup subsys cpuacct
[ 0.061392] Initializing cgroup subsys memory
[ 0.061399] Initializing cgroup subsys devices
[ 0.061426] CPU: Trace cache: 12K uops, L1 D cache: 8K
[ 0.061431] CPU: L2 cache: 256K
[ 0.061436] CPU: Hyper-Threading is disabled
[ 0.061442] Intel machine check architecture supported.
[ 0.061450] Intel machine check reporting enabled on CPU#0.
[ 0.061455] CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
[ 0.061462] CPU0: Thermal monitoring enabled
[ 0.061489] Checking 'hlt' instruction... OK.
[ 0.066754] ACPI: Core revision 20080321
[ 0.104100] ENABLING IO-APIC IRQs
[ 0.104337] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.114353] CPU0: Intel(R) Pentium(R) 4 CPU 1.70GHz stepping 02
[ 0.114982] Brought up 1 CPUs
[ 0.114982] Total of 1 processors activated (3393.04 BogoMIPS).
[ 0.114982] net_namespace: 660 bytes
[ 0.115051] xor: automatically using best checksumming function: pIII_sse
[ 0.119988] pIII_sse : 2240.000 MB/sec
[ 0.119994] xor: using function: pIII_sse (2240.000 MB/sec)
[ 0.120072] NET: Registered protocol family 16
[ 0.120795] No dock devices found.
[ 0.121213] EISA bus registered
[ 0.121233] ACPI: bus type pci registered
[ 0.147325] PCI: PCI BIOS revision 2.10 entry at 0xfbe2e, last bus=2
[ 0.147332] PCI: Using configuration type 1 for base access
[ 0.147367] Setting up standard PCI resources
[ 0.157738] ACPI: EC: Look up EC in DSDT
[ 0.183881] ACPI: Interpreter enabled
[ 0.183894] ACPI: (supports S0 S1 S3 S4 S5)
[ 0.183932] ACPI: Using IOAPIC for interrupt routing
[ 0.213735] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.214186] pci 0000:00:1f.0: quirk: region 0800-087f claimed by ICH4 ACPI/GPIO/TCO
[ 0.214195] pci 0000:00:1f.0: quirk: region 0880-08bf claimed by ICH4 GPIO
[ 0.214845] PCI: Transparent bridge - 0000:00:1e.0
[ 0.214889] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.215510] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
[ 0.237318] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 15)
[ 0.237714] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 *10 11 12 15)
[ 0.238124] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 *11 12 15)
[ 0.238510] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11 12 15)
[ 0.238894] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 15) *0, disabled.
[ 0.239285] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 15) *0, disabled.
[ 0.239669] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 11 12 15) *0, disabled.
[ 0.240068] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 *9 10 11 12 15)
[ 0.240654] ACPI: WMI: Mapper loaded
[ 0.240661] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 0.240749] pnp: PnP ACPI init
[ 0.240772] ACPI: bus type pnp registered
[ 0.268618] pnp: PnP ACPI: found 12 devices
[ 0.268628] ACPI: ACPI bus type pnp unregistered
[ 0.268639] PnPBIOS: Disabled by ACPI PNP
[ 0.269294] SCSI subsystem initialized
[ 0.269389] libata version 3.00 loaded.
[ 0.269935] usbcore: registered new interface driver usbfs
[ 0.270147] usbcore: registered new interface driver hub
[ 0.270266] usbcore: registered new device driver usb
[ 0.270846] PCI: Using ACPI for IRQ routing
[ 0.283600] ACPI: RTC can wake from S4
[ 0.283735] system 00:00: iomem range 0x0-0x9ffff could not be reserved
[ 0.283744] system 00:00: iomem range 0x100000-0xffffff could not be reserved
[ 0.283750] system 00:00: iomem range 0x1000000-0x1ff76fff could not be reserved
[ 0.283755] system 00:00: iomem range 0xf0000-0xfffff could not be reserved
[ 0.283762] system 00:00: iomem range 0xfec00000-0xfec0ffff could not be reserved
[ 0.283768] system 00:00: iomem range 0xfee00000-0xfee0ffff could not be reserved
[ 0.283774] system 00:00: iomem range 0xffb00000-0xffbfffff could not be reserved
[ 0.283780] system 00:00: iomem range 0xffc00000-0xffffffff could not be reserved
[ 0.283820] system 00:0b: ioport range 0x800-0x85f has been reserved
[ 0.283825] system 00:0b: ioport range 0xc00-0xc7f has been reserved
[ 0.283831] system 00:0b: ioport range 0x860-0x8ff could not be reserved
[ 0.314265] PCI: Bridge: 0000:00:01.0
[ 0.314273] IO window: e000-efff
[ 0.314281] MEM window: 0xff800000-0xff9fffff
[ 0.314288] PREFETCH window: 0x00000000f8000000-0x00000000fbffffff
[ 0.314299] PCI: Bridge: 0000:00:1e.0
[ 0.314304] IO window: d000-dfff
[ 0.314313] MEM window: 0xff600000-0xff7fffff
[ 0.314320] PREFETCH window: 0x0000000030000000-0x00000000300fffff
[ 0.314349] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[ 0.314380] NET: Registered protocol family 2
[ 0.314609] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.315113] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.315313] TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.315524] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.315530] TCP reno registered
[ 0.315917] NET: Registered protocol family 1
[ 0.316228] checking if image is initramfs... it is
[ 0.773191] Freeing initrd memory: 4173k freed
[ 0.773615] Simple Boot Flag at 0x7a set to 0x1
[ 0.775023] audit: initializing netlink socket (disabled)
[ 0.775058] type=2000 audit(1027906686.774:1): initialized
[ 0.775304] Total HugeTLB memory allocated, 0
[ 0.780878] VFS: Disk quotas dquot_6.5.1
[ 0.780960] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.782833] squashfs: version 3.3 (2007/10/31) Phillip Lougher
[ 0.784961] Registering unionfs 2.4 (for 2.6.26)
[ 0.785917] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 0.787957] NTFS driver 2.1.29 [Flags: R/W].
[ 0.788707] QNX4 filesystem 0.2.3 registered.
[ 0.789188] aufs 20080609
[ 0.789195] fuse init (API version 7.9)
[ 0.790161] JFS: nTxBlock = 3958, nTxLock = 31666
[ 0.797119] SGI XFS with ACLs, security attributes, realtime, large block numbers, no debug enabled
[ 0.799379] SGI XFS Quota Management subsystem
[ 0.799420] msgmni has been set to 989
[ 0.799834] async_tx: api initialized (async)
[ 0.800199] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.800211] io scheduler noop registered
[ 0.800216] io scheduler anticipatory registered
[ 0.800219] io scheduler deadline registered
[ 0.800282] io scheduler cfq registered (default)
[ 0.800366] pci 0000:01:00.0: Boot video device
[ 0.814759] Switched to high resolution mode on CPU 0
[ 0.898288] lp: driver loaded but no devices found
[ 0.898672] toshiba: not a supported Toshiba laptop
[ 0.898826] intel_rng: FWH not detected
[ 0.918099] ppdev: user-space parallel port driver
[ 0.918109] Linux agpgart interface v0.103
[ 0.918606] uvesafb: failed to execute /sbin/v86d
[ 0.918621] uvesafb: make sure that the v86d helper is installed and executable
[ 0.918630] uvesafb: Getting VBE info block failed (eax=0x4f00, err=-2)
[ 0.918639] uvesafb: vbe_init() failed with -22
[ 0.918656] uvesafb: probe of uvesafb.0 failed with error -22
[ 0.919008] vesafb: framebuffer at 0xf8000000, mapped to 0xe0a80000, using 3072k, total 32768k
[ 0.919013] vesafb: mode is 1024x768x16, linelength=2048, pages=20
[ 0.919039] vesafb: protected mode interface info at c000:441b
[ 0.919045] vesafb: pmi: set display start = c00c4489, set palette = c00c44c3
[ 0.919049] vesafb: pmi: ports = e010 e016 e054 e038 e03c e05c e000 e004 e0b0 e0b2 e0b4
[ 0.919070] vesafb: scrolling: redraw
[ 0.919076] vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
[ 0.963965] Console: switching to colour frame buffer device 128x48
[ 1.170187] fbcondecor: console 0 using theme 'sabayon'
[ 1.290203] fbcondecor: switched decor state to 'on' on console 0
[ 1.293199] fb0: VESA VGA frame buffer device
[ 1.293444] vga16fb: initializing
[ 1.293452] vga16fb: mapped to 0xc00a0000
[ 1.293594] fb1: VGA16 VGA frame buffer device
[ 1.293822] input: Power Button (FF) as /class/input/input0
[ 1.293921] ACPI: Power Button (FF) [PWRF]
[ 1.294169] input: Power Button (CM) as /class/input/input1
[ 1.294224] ACPI: Power Button (CM) [VBTN]
[ 1.294914] ACPI: ACPI0007:00 is registered as cooling_device0
[ 1.311004] isapnp: Scanning for PnP cards...
[ 1.624436] isapnp: No Plug & Play device found
[ 1.624447] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 1.868171] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 2.112168] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 2.114001] 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 2.114972] 00:09: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 2.115745] parport_pc 00:0a: reported by Plug and Play ACPI
[ 2.115806] parport0: PC-style at 0x378 (0x778), irq 7, using FIFO [PCSPP,TRISTATE,COMPAT,ECP]
[ 2.198420] lp0: using parport0 (interrupt-driven).
[ 2.198427] lp0: console ready
[ 2.199543] Floppy drive(s): fd0 is 1.44M
[ 2.212141] FDC 0 is a post-1991 82077
[ 2.217042] brd: module loaded
[ 2.218945] loop: module loaded
[ 2.218954] Compaq SMART2 Driver (v 2.6.0)
[ 2.219124] HP CISS Driver (v 3.6.20)
[ 2.219801] MM: desc_per_page = 128
[ 2.220337] input: Macintosh mouse button emulation as /class/input/input2
[ 2.220925] Loading iSCSI transport class v2.0-869.
[ 2.222106] iscsi: registered transport (tcp)
[ 2.225135] Loading Adaptec I2O RAID: Version 2.4 Build 5go
[ 2.225142] Detecting Adaptec I2O RAID controllers...
[ 2.226608] Adaptec aacraid driver 1.1-5[2456]-ms
[ 2.227131] aic94xx: Adaptec aic94xx SAS/SATA driver version 1.0.3 loaded
[ 2.227677] NCR53c406a: no available ports found
[ 2.227688] sym53c416.c: Version 1.0.0-ac
[ 2.227724] qlogicfas: no cards were found, please specify I/O address and IRQ using iobase= and irq= options<6>QLogic Fibre Channel HBA Driver: 8.02.01-k4
[ 2.228385] iscsi: registered transport (qla4xxx)
[ 2.228520] QLogic iSCSI HBA Driver
[ 2.228526] Emulex LightPulse Fibre Channel SCSI driver 8.2.6
[ 2.228530] Copyright(c) 2004-2008 Emulex. All rights reserved.
[ 2.250060] Failed initialization of WD-7000 SCSI card!
[ 2.684004] DC390: clustering now enabled by default. If you get problems load
[ 2.684004] with "disable_clustering=1" and report to maintainers
[ 2.684004] megaraid cmm: 2.20.2.7 (Release Date: Sun Jul 16 00:01:03 EST 2006)
[ 2.684004] megaraid: 2.20.5.1 (Release Date: Thu Nov 16 15:32:35 EST 2006)
[ 2.684004] megasas: 00.00.03.20-rc1 Mon. March 10 11:02:31 PDT 2008
[ 2.684004] GDT-HA: Storage RAID Controller Driver. Version: 3.05
[ 2.684247] 3ware Storage Controller device driver for Linux v1.26.02.002.
[ 2.684357] 3ware 9000 Storage Controller device driver for Linux v2.26.02.010.
[ 2.684469] nsp32: loading...
[ 2.684581] ipr: IBM Power RAID SCSI Device Driver version: 2.4.1 (April 24, 2007)
[ 2.684693] RocketRAID 3xxx/4xxx Controller driver v1.3 (071203)
[ 2.684804] stex: Promise SuperTrak EX Driver version: 3.6.0000.1
[ 2.685009] st: Version 20080224, fixed bufsize 32768, s/g segs 256
[ 2.685134] Driver 'st' needs updating - please use bus_type methods
[ 2.685246] osst :I: Tape driver with OnStream support version 0.99.4
[ 2.685249] osst :I: $Id: osst.c,v 1.73 2005/01/01 21:13:34 wriede Exp $
[ 2.685339] Driver 'osst' needs updating - please use bus_type methods
[ 2.685526] Driver 'sd' needs updating - please use bus_type methods
[ 2.685608] Driver 'sr' needs updating - please use bus_type methods
[ 2.686181] ata_piix 0000:00:1f.1: version 2.12
[ 2.686313] PCI: Setting latency timer of device 0000:00:1f.1 to 64
[ 2.686465] scsi2 : ata_piix
[ 2.686870] scsi3 : ata_piix
[ 2.687058] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14
[ 2.687065] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15
[ 2.844461] ata1.00: ATA-5: ST340016A, 3.10, max UDMA/100
[ 2.844468] ata1.00: 78165360 sectors, multi 8: LBA
[ 2.891204] ata1.01: ATA-7: ST3320620A, 3.AAC, max UDMA/100
[ 2.891204] ata1.01: 625142448 sectors, multi 8: LBA48
[ 2.897391] ata1.00: configured for UDMA/100
[ 2.949511] ata1.01: configured for UDMA/100
[ 3.089981] ata2.01: both IDENTIFYs aborted, assuming NODEV
[ 3.103379] ata2.00: ATAPI: CW058D ATAPI CD-R/RW, V12HD, max UDMA/33
[ 3.109354] ata2.00: configured for UDMA/33
[ 3.109598] scsi 2:0:0:0: Direct-Access ATA ST340016A 3.10 PQ: 0 ANSI: 5
[ 3.110158] sd 2:0:0:0: [sda] 78165360 512-byte hardware sectors (40021 MB)
[ 3.110197] sd 2:0:0:0: [sda] Write Protect is off
[ 3.110202] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 3.110260] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3.110405] sd 2:0:0:0: [sda] 78165360 512-byte hardware sectors (40021 MB)
[ 3.110438] sd 2:0:0:0: [sda] Write Protect is off
[ 3.110443] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 3.110497] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3.110505] sda: sda1 sda2
[ 3.128307] sd 2:0:0:0: [sda] Attached SCSI disk
[ 3.128577] sd 2:0:0:0: Attached scsi generic sg0 type 0
[ 3.128942] scsi 2:0:1:0: Direct-Access ATA ST3320620A 3.AA PQ: 0 ANSI: 5
[ 3.129435] sd 2:0:1:0: [sdb] 625142448 512-byte hardware sectors (320073 MB)
[ 3.129473] sd 2:0:1:0: [sdb] Write Protect is off
[ 3.129479] sd 2:0:1:0: [sdb] Mode Sense: 00 3a 00 00
[ 3.129537] sd 2:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3.129680] sd 2:0:1:0: [sdb] 625142448 512-byte hardware sectors (320073 MB)
[ 3.129712] sd 2:0:1:0: [sdb] Write Protect is off
[ 3.129717] sd 2:0:1:0: [sdb] Mode Sense: 00 3a 00 00
[ 3.129771] sd 2:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3.129777] sdb: sdb1
[ 3.147406] sd 2:0:1:0: [sdb] Attached SCSI disk
[ 3.148219] sd 2:0:1:0: Attached scsi generic sg1 type 0
[ 3.149242] scsi 3:0:0:0: CD-ROM CyberDrv CW058D CD-R/RW 12HD PQ: 0 ANSI: 5
[ 3.152445] sr0: scsi3-mmc drive: 4x/40x writer cd/rw xa/form2 cdda tray
[ 3.152445] Uniform CD-ROM driver Revision: 3.20
[ 3.152445] sr 3:0:0:0: Attached scsi CD-ROM sr0
[ 3.153174] sr 3:0:0:0: Attached scsi generic sg2 type 5
[ 3.160598] I2O subsystem v1.325
[ 3.160606] i2o: max drivers = 8
[ 3.160996] I2O Configuration OSM v1.323
[ 3.161298] I2O Bus Adapter OSM v1.317
[ 3.161378] I2O Block Device OSM v1.325
[ 3.161799] I2O SCSI Peripheral OSM v1.316
[ 3.161889] I2O ProcFS OSM v1.316
[ 3.161985] Fusion MPT base driver 3.04.06
[ 3.161990] Copyright (c) 1999-2007 LSI Corporation
[ 3.162000] Fusion MPT SPI Host driver 3.04.06
[ 3.162227] Fusion MPT FC Host driver 3.04.06
[ 3.162401] Fusion MPT SAS Host driver 3.04.06
[ 3.162573] Fusion MPT misc device (ioctl) driver 3.04.06
[ 3.162684] mptctl: Registered with Fusion MPT base driver
[ 3.162690] mptctl: /dev/mptctl @ (major,minor=10,220)
[ 3.162694] Fusion MPT LAN driver 3.04.06
[ 3.163944] usbcore: registered new interface driver usblp
[ 3.163954] Initializing USB Mass Storage driver...
[ 3.164071] usbcore: registered new interface driver usb-storage
[ 3.164080] USB Mass Storage support registered.
[ 3.164178] usbcore: registered new interface driver libusual
[ 3.164439] PNP: PS/2 Controller [PNP0303:KBD] at 0x60,0x64 irq 1
[ 3.164445] PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
[ 3.164941] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 3.164963] parport0: cannot grant exclusive access for device parkbd
[ 3.165848] mice: PS/2 mouse device common for all mice
[ 3.183007] input: AT Translated Set 2 keyboard as /class/input/input3
[ 3.200457] md: linear personality registered for level -1
[ 3.200464] md: raid0 personality registered for level 0
[ 3.200470] md: raid1 personality registered for level 1
[ 3.200474] md: raid10 personality registered for level 10
[ 3.217066] raid6: int32x1 417 MB/s
[ 3.234034] raid6: int32x2 527 MB/s
[ 3.251067] raid6: int32x4 609 MB/s
[ 3.268074] raid6: int32x8 367 MB/s
[ 3.285023] raid6: mmxx1 1398 MB/s
[ 3.302042] raid6: mmxx2 1753 MB/s
[ 3.319029] raid6: sse1x1 886 MB/s
[ 3.336035] raid6: sse1x2 1507 MB/s
[ 3.353023] raid6: sse2x1 1750 MB/s
[ 3.370012] raid6: sse2x2 1890 MB/s
[ 3.370017] raid6: using algorithm sse2x2 (1890 MB/s)
[ 3.370023] md: raid6 personality registered for level 6
[ 3.370027] md: raid5 personality registered for level 5
[ 3.370031] md: raid4 personality registered for level 4
[ 3.370036] md: multipath personality registered for level -4
[ 3.370040] md: faulty personality registered for level -5
[ 3.370467] device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised: dm-devel@redhat.com
[ 3.370667] EDAC MC: Ver: 2.1.0 Aug 9 2008
[ 3.371329] EISA: Probing bus 0 at eisa.0
[ 3.371393] EISA: Detected 0 cards.
[ 3.371462] cpuidle: using governor ladder
[ 3.371467] cpuidle: using governor menu
[ 3.371714] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2)
[ 3.371952] usbcore: registered new interface driver hiddev
[ 3.372105] usbcore: registered new interface driver usbhid
[ 3.372114] usbhid: v2.6:USB HID core driver
[ 3.373766] TCP bic registered
[ 3.373775] NET: Registered protocol family 17
[ 3.374380] RPC: Registered udp transport module.
[ 3.374387] RPC: Registered tcp transport module.
[ 3.374450] Using IPI No-Shortcut mode
[ 3.374846] TuxOnIce 3.0-rc7 (http://tuxonice.net)
[ 3.374995] registered taskstats version 1
[ 3.375206] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 3.376690] Freeing unused kernel memory: 552k freed
[ 4.410222] USB Universal Host Controller Interface driver v3.0
[ 4.410440] ACPI: PCI Interrupt 0000:00:1f.2[D] -> GSI 19 (level, low) -> IRQ 19
[ 4.410464] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[ 4.410472] uhci_hcd 0000:00:1f.2: UHCI Host Controller
[ 4.410859] uhci_hcd 0000:00:1f.2: new USB bus registered, assigned bus number 1
[ 4.410910] uhci_hcd 0000:00:1f.2: irq 19, io base 0x0000ff80
[ 4.411275] usb usb1: configuration #1 chosen from 1 choice
[ 4.411424] hub 1-0:1.0: USB hub found
[ 4.411453] hub 1-0:1.0: 2 ports detected
[ 4.512677] ACPI: PCI Interrupt 0000:00:1f.4[C] -> GSI 23 (level, low) -> IRQ 23
[ 4.512702] PCI: Setting latency timer of device 0000:00:1f.4 to 64
[ 4.512709] uhci_hcd 0000:00:1f.4: UHCI Host Controller
[ 4.512989] uhci_hcd 0000:00:1f.4: new USB bus registered, assigned bus number 2
[ 4.513060] uhci_hcd 0000:00:1f.4: irq 23, io base 0x0000ff60
[ 4.513354] usb usb2: configuration #1 chosen from 1 choice
[ 4.513498] hub 2-0:1.0: USB hub found
[ 4.513521] hub 2-0:1.0: 2 ports detected
[ 4.718070] usb 1-2: new low speed USB device using uhci_hcd and address 2
[ 4.882602] sl811: driver sl811-hcd, 19 May 2005
[ 4.887761] usb 1-2: configuration #1 chosen from 1 choice
[ 4.932747] input: Microsoft Microsoft USB Wireless Mouse as /class/input/input4
[ 4.943115] input,hidraw0: USB HID v1.11 Mouse [Microsoft Microsoft USB Wireless Mouse] on usb-0000:00:1f.2-2
[ 5.988732] Intel(R) PRO/1000 Network Driver - version 7.3.20-k2
[ 5.988741] Copyright (c) 1999-2006 Intel Corporation.
[ 19.607149] TuxOnIce: Normal swapspace found.
[ 19.629210] TuxOnIce: Failed to initialise the lzf compression transform.
[ 19.647109] EXT3-fs: INFO: recovery required on readonly filesystem.
[ 19.647109] EXT3-fs: write access will be enabled during recovery.
[ 23.548003] kjournald starting. Commit interval 5 seconds
[ 23.548003] EXT3-fs: recovery complete.
[ 23.675335] EXT3-fs: mounted filesystem with ordered data mode.
[ 30.638869] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 30.669488] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 30.760720] iTCO_vendor_support: vendor-support=0
[ 30.783138] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.03 (30-Apr-2008)
[ 30.783298] iTCO_wdt: Found a ICH2 TCO device (Version=1, TCOBASE=0x0860)
[ 30.783354] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 31.042780] ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 17 (level, low) -> IRQ 17
[ 31.075734] agpgart: Detected an Intel 845G Chipset.
[ 31.083576] agpgart: AGP aperture is 128M @ 0xf0000000
[ 31.233882] input: PC Speaker as /class/input/input5
[ 31.493642] ACPI: PCI Interrupt 0000:02:0c.0[A] -> GSI 18 (level, low) -> IRQ 18
[ 31.493667] 3c59x: Donald Becker and others.
[ 31.493679] 0000:02:0c.0: 3Com PCI 3c905C Tornado at e0f76c00.
[ 31.675255] ACPI: PCI Interrupt 0000:00:1f.5[B] -> GSI 17 (level, low) -> IRQ 17
[ 31.675294] PCI: Setting latency timer of device 0000:00:1f.5 to 64
[ 32.288019] intel8x0_measure_ac97_clock: measured 50958 usecs
[ 32.288026] intel8x0: clocking to 41138
[ 58.092692] fbcondecor: console 0 using theme 'sabayon'
[ 58.167499] fbcondecor: switched decor state to 'on' on console 0
[ 133.549785] EXT3 FS on dm-0, internal journal
[ 161.656712] kjournald starting. Commit interval 5 seconds
[ 161.656712] EXT3 FS on sda1, internal journal
[ 161.656712] EXT3-fs: mounted filesystem with ordered data mode.
[ 364.794822] Adding 1015800k swap on /dev/mapper/VolGroup00-LogVol01. Priority:-1 extents:1 across:1015800k
[ 414.487712] [drm] Initialized drm 1.1.0 20060810
[ 414.497681] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 414.497963] [drm] Initialized r128 2.5.0 20030725 on minor 0
[ 414.499734] agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
[ 414.499772] agpgart: Putting AGP V2 device at 0000:00:00.0 into 1x mode
[ 414.499811] agpgart: Putting AGP V2 device at 0000:01:00.0 into 1x mode
[ 471.455679] eth0: setting full-duplex.
[ 486.282891] fbcondecor: console 1 using theme 'sabayon'
[ 486.516016] fbcondecor: switched decor state to 'on' on console 1
[ 486.779253] fbcondecor: console 2 using theme 'sabayon'
[ 487.018536] fbcondecor: switched decor state to 'on' on console 2
[ 487.280256] fbcondecor: console 3 using theme 'sabayon'
[ 487.517703] fbcondecor: switched decor state to 'on' on console 3
[ 487.773426] fbcondecor: console 4 using theme 'sabayon'
[ 488.003145] fbcondecor: switched decor state to 'on' on console 4
[ 488.264043] fbcondecor: console 5 using theme 'sabayon'
[ 488.501309] fbcondecor: switched decor state to 'on' on console 5
[ 517.627182] warning: `avahi-daemon' uses 32-bit capabilities (legacy support in use)
[ 517.778178] NET: Registered protocol family 10
[ 517.780096] lo: Disabled Privacy Extensions
[ 527.959049] eth0: no IPv6 routers present

[chickenhawk]

So am I being discriminated against, I posted dmesg and what lead to the error. I already searched on google and here in the forum, if this has been solved before I'm just not using the correct search terms on the forum. Anyway I figured it out and this is the fourth time in a year I posted a question after vigorously searching through the forum after doing so on google and I still get shafted. Is it because I'm american? All I can do to get the neocons out of office is vote, and from what I hear that is being compromised because of those sorry diebold machines. I just don't have the power man, and I don't have the cheese to move somewhere else. Well that's just cruel and unusual to do me like that.

[wolfden]

how about posting in the correct forum for one?

nobody is prejudice here, good grief.

This is the first I seen this post and there really isn't enough info to make heads or tails of anything - no other logs, we don't even no which sabayon linux for sure. There is 4 flavors of 3.5. No mention of what you have and haven't tried. Srsly, our crystal balls only can do so much.

Please see:
viewtopic.php?f=50&t=8518

[Stupot]

You're not being discriminated against, but if people don't know what's wrong, it's kind of silly for them to post just to say "I dunno". FYI, I'm American as well

[joost]

gah americans..

I usually only help Europians, but hey...

If the system boots up, you can press alt+f1 to see thats happening.

[stevencomerthornley]

so how did it get solved??????????