no wireless sabayon 3.4; rt2500

[federoco]

Calculating dependencies... done!
>>> Verifying ebuild Manifests...

>>> Emerging (1 of 1) net-wireless/rt2x00-9999 to /
* checking ebuild checksums ;-) ... [ ok ]
* checking auxfile checksums ;-) ... [ ok ]
* checking miscfile checksums ;-) ... [ ok ]
* Determining the location of the kernel source code
* Found kernel source directory:
* /usr/src/linux
* Found kernel object directory:
* /lib/modules/2.6.22-sabayon/build
* Found sources for kernel version:
* 2.6.22-sabayon
* Checking for suitable kernel configuration options...
* rt2x00-9999 requires support for Wireless LAN drivers (non-hamradio) & Wireless Extensions (CONFIG_NET_RADIO).
* Please check to make sure these options are set correctly.
* Failure to do so may cause unexpected problems.
* Once you have satisfied these options, please try merging
* this package again.

!!! ERROR: net-wireless/rt2x00-9999 failed.
Call stack:
ebuild.sh, line 1637: Called dyn_setup
ebuild.sh, line 704: Called qa_call 'pkg_setup'
ebuild.sh, line 44: Called pkg_setup
rt2x00-9999.ebuild, line 60: Called linux-mod_pkg_setup
linux-mod.eclass, line 464: Called linux-info_pkg_setup
linux-info.eclass, line 572: Called check_extra_config
linux-info.eclass, line 471: Called die

!!! Incorrect kernel configuration options
!!! If you need support, post the topmost build error, and the call stack if relevant.
!!! A complete build log is located at '/var/tmp/portage/net-wireless/rt2x00-9999/temp/build.log'.


I tried to install the driver, but i cant...

[Dark_MaGe]

rt2500 is already inkernel why are you emerging that? if you have problems with the already included driver post a dmesg and iwconfig

[federoco]

Ok, I will. Its strange, because my usb rt2500 wifi antenna can connect, but the broatcom (rt2500 wifi chipset too), cannot.

[Dark_MaGe]

Ok, I will. Its strange, because my usb rt2500 wifi antenna can connect, but the broatcom (rt2500 wifi chipset too), cannot.

again post dmesg and iwconfig and lspci, without looking at those I can't help you much

[federoco]

ok, sorry:

localhost federoco # iwconfig
lo no wireless extensions.

eth0 no wireless extensions.

wmaster0 no wireless extensions.

wlan0 IEEE 802.11g ESSID:""
Mode:Managed Frequency:2.412 GHz Access Point: Not-Associated
Retry min limit:7 RTS thr:off Fragment thr=2346 B
Encryption key:off
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0

eth1 IEEE 802.11b/g ESSID:"comtrendf" Nickname:"zd1211"
Mode:Managed Frequency:2.417 GHz Access Point: 00:03:C9:E6:2A:F8
Bit Rate=24 Mb/s
Encryption key:3538-3734-6173-6465-7266-6564-65 Security mode:open
Link Quality=100/100 Signal level=57/100
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0

--------------------------------------------------------

localhost federoco # lspci
00:00.0 Host bridge: ATI Technologies Inc RS480 Host Bridge (rev 01)
00:01.0 PCI bridge: ATI Technologies Inc RS480 PCI Bridge
00:10.0 CardBus bridge: Texas Instruments PCIxx21/x515 Cardbus Controller
00:10.2 FireWire (IEEE 1394): Texas Instruments OHCI Compliant IEEE 1394 Host Controller
00:10.3 Mass storage controller: Texas Instruments PCIxx21 Integrated FlashMedia Controller
00:10.4 Generic system peripheral [0805]: Texas Instruments PCI6411/6421/6611/6621/7411/7421/7611/7621 Secure Digital Controller
00:11.0 Network controller: RaLink RT2500 802.11g Cardbus/mini-PCI (rev 01)
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
00:19.0 PCI bridge: ALi Corporation M5249 HTT to PCI Bridge
00:1b.0 Ethernet controller: ALi Corporation ULi 1689,1573 integrated ethernet. (rev 50)
00:1c.0 USB Controller: ALi Corporation USB 1.1 Controller (rev 03)
00:1c.1 USB Controller: ALi Corporation USB 1.1 Controller (rev 03)
00:1c.2 USB Controller: ALi Corporation USB 1.1 Controller (rev 03)
00:1c.3 USB Controller: ALi Corporation USB 2.0 Controller (rev 01)
00:1d.0 Audio device: ALi Corporation High Definition Audio/AC'97 Host Controller
00:1e.0 ISA bridge: ALi Corporation PCI to LPC Controller (rev 31)
00:1e.1 Bridge: ALi Corporation M7101 Power Management Controller [PMU]
00:1f.0 IDE interface: ALi Corporation M5229 IDE (rev c7)
00:1f.1 RAID bus controller: ALi Corporation ULi 5287 SATA (rev 02)
01:05.0 VGA compatible controller: ATI Technologies Inc Radeon XPRESS 200M 5955 (PCIE)


---------------------------------------------------------------

localhost federoco # dmesg
t range 0x480-0x48f has been reserved
[ 7.810364] pnp: 00:07: ioport range 0x330-0x331 has been reserved
[ 7.810368] pnp: 00:07: ioport range 0x4d0-0x4d1 has been reserved
[ 7.810372] pnp: 00:07: ioport range 0x1000-0x107f could not be reserved
[ 7.810375] pnp: 00:07: ioport range 0x1400-0x140f has been reserved
[ 7.810509] ACPI: PCI Interrupt 0000:00:10.2[C] -> GSI 19 (level, low) -> IRQ 19
[ 7.810574] Device driver fw-host0 lacks bus and class support for being resumed.
[ 7.860920] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[19] MMIO=[d0000000-d00007ff] Max Packet=[2048] IR/IT contexts=[4/8]
[ 7.861030] PCI: Bridge: 0000:00:01.0
[ 7.861033] IO window: c000-dfff
[ 7.861037] MEM window: c0000000-cfffffff
[ 7.861040] PREFETCH window: 90000000-9fffffff
[ 7.861044] PCI: Bus 3, cardbus bridge: 0000:00:10.0
[ 7.861046] IO window: 00001800-000018ff
[ 7.861052] IO window: 00001c00-00001cff
[ 7.861057] PREFETCH window: 40000000-43ffffff
[ 7.861063] MEM window: 44000000-47ffffff
[ 7.861068] PCI: Bridge: 0000:00:19.0
[ 7.861072] IO window: a000-bfff
[ 7.861077] MEM window: b8000000-bfffffff
[ 7.861082] PREFETCH window: 88000000-8fffffff
[ 7.861107] PCI: Enabling device 0000:00:10.0 (0000 -> 0003)
[ 7.861112] ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 7.861123] PCI: Setting latency timer of device 0000:00:10.0 to 64
[ 7.861135] PCI: Setting latency timer of device 0000:00:19.0 to 64
[ 7.861224] NET: Registered protocol family 2
[ 7.870973] IP route cache hash table entries: 32768 (order: 6, 262144 bytes)
[ 7.871724] TCP established hash table entries: 131072 (order: 9, 3145728 bytes)
[ 7.874836] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 7.875943] TCP: Hash tables configured (established 131072 bind 65536)
[ 7.875947] TCP reno registered
[ 7.879064] checking if image is initramfs... it is
[ 8.158855] Freeing initrd memory: 4090k freed
[ 8.163305] audit: initializing netlink socket (disabled)
[ 8.163322] audit(1185998092.486:1): initialized
[ 8.163384] Total HugeTLB memory allocated, 0
[ 8.163495] VFS: Disk quotas dquot_6.5.1
[ 8.163505] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 8.163607] squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
[ 8.163610] Registering unionfs 20060916-2203
[ 8.163612] unionfs: debugging is not enabled
[ 8.163644] Coda Kernel/Venus communications, v5.3.20, coda@cs.cmu.edu
[ 8.163964] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 8.164312] NTFS driver 2.1.28 [Flags: R/W].
[ 8.164360] QNX4 filesystem 0.2.3 registered.
[ 8.164364] fuse init (API version 7.
[ 8.164478] JFS: nTxBlock = 6985, nTxLock = 55887
[ 8.169377] SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled
[ 8.169552] SGI XFS Quota Management subsystem
[ 8.169597] SELinux: Registering netfilter hooks
[ 8.169743] io scheduler noop registered
[ 8.169746] io scheduler anticipatory registered
[ 8.169748] io scheduler deadline registered
[ 8.169766] io scheduler cfq registered (default)
[ 8.169773] PCI: MSI quirk detected. MSI deactivated.
[ 8.246619] Boot video device is 0000:01:05.0
[ 8.279617] lp: driver loaded but no devices found
[ 8.279721] Real Time Clock Driver v1.12ac
[ 8.284572] ppdev: user-space parallel port driver
[ 8.284578] Linux agpgart interface v0.102 (c) Dave Jones
[ 8.284711] vesafb: framebuffer at 0x90000000, mapped to 0xffffc20000b00000, using 3072k, total 131072k
[ 8.284716] vesafb: mode is 1024x768x16, linelength=2048, pages=84
[ 8.284718] vesafb: scrolling: redraw
[ 8.284721] vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
[ 8.293757] Console: switching to colour frame buffer device 128x48
[ 8.303305] fbsplash: console 0 using theme 'sabayon'
[ 8.478462] fbsplash: switched splash state to 'on' on console 0
[ 8.478891] fb0: VESA VGA frame buffer device
[ 8.480986] ACPI: AC Adapter [AC] (on-line)
[ 8.483283] ACPI: Battery Slot [BAT0] (battery present)
[ 8.483407] input: Power Button (FF) as /class/input/input0
[ 8.483412] ACPI: Power Button (FF) [PWRF]
[ 8.483482] input: Power Button (CM) as /class/input/input1
[ 8.483489] ACPI: Power Button (CM) [PBTN]
[ 8.483564] input: Sleep Button (CM) as /class/input/input2
[ 8.483568] ACPI: Sleep Button (CM) [SBTN]
[ 8.483640] input: Lid Switch as /class/input/input3
[ 8.483643] ACPI: Lid Switch [LID]
[ 8.483849] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
[ 8.483853] ACPI: Processor [CPU0] (supports 8 throttling states)
[ 8.485238] ibm_acpi: ec object not found
[ 8.485245] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 8.486119] PCI driver parport_pc lacks driver specific resume support.
[ 8.495821] Marking TSC unstable due to possible TSC halt in C2
[ 8.495827] Time: acpi_pm clocksource has been installed.
[ 9.179770] Device driver 0040d0010033a9e1 lacks bus and class support for being resumed.
[ 9.179810] ieee1394: Host added: ID:BUS[0-00:1023] GUID[0040d0010033a9e1]
[ 11.491790] floppy0: no floppy controllers found
[ 11.492408] RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
[ 11.492718] loop: module loaded
[ 11.492720] Compaq SMART2 Driver (v 2.6.0)
[ 11.492773] PCI driver cpqarray lacks driver specific resume support.
[ 11.492776] HP CISS Driver (v 3.6.14)
[ 11.492822] PCI driver cciss lacks driver specific resume support.
[ 11.492855] PCI driver DAC960 lacks driver specific resume support.
[ 11.492976] v2.3 : Micro Memory(tm) PCI memory board block driver
[ 11.493015] PCI driver umem lacks driver specific resume support.
[ 11.493019] MM: desc_per_page = 128
[ 11.493090] Device driver lo lacks bus and class support for being resumed.
[ 11.493161] PCI driver hp100 lacks driver specific resume support.
[ 11.493239] input: Macintosh mouse button emulation as /class/input/input4
[ 11.493270] Loading iSCSI transport class v2.0-724.
[ 11.493385] iscsi: registered transport (tcp)
[ 11.493496] PCI driver arcmsr lacks driver specific resume support.
[ 11.493555] PCI driver aic7xxx lacks driver specific resume support.
[ 11.493620] PCI driver aic79xx lacks driver specific resume support.
[ 11.493623] Adaptec aacraid driver (1.1-5[2437]-mh4)
[ 11.493671] PCI driver aacraid lacks driver specific resume support.
[ 11.493695] aic94xx: Adaptec aic94xx SAS/SATA driver version 1.0.3 loaded
[ 11.493765] PCI driver aic94xx lacks driver specific resume support.
[ 11.493809] PCI driver ips lacks driver specific resume support.
[ 11.493876] PCI driver qla1280 lacks driver specific resume support.
[ 11.493893] QLogic Fibre Channel HBA Driver
[ 11.493935] PCI driver qla2xxx lacks driver specific resume support.
[ 11.493981] iscsi: registered transport (qla4xxx)
[ 11.494019] PCI driver qla4xxx lacks driver specific resume support.
[ 11.494022] QLogic iSCSI HBA Driver
[ 11.494024] Emulex LightPulse Fibre Channel SCSI driver 8.1.12
[ 11.494026] Copyright(c) 2004-2007 Emulex. All rights reserved.
[ 11.494073] PCI driver lpfc lacks driver specific resume support.
[ 11.494107] PCI driver dmx3191d lacks driver specific resume support.
[ 11.494157] PCI driver sym53c8xx lacks driver specific resume support.
[ 11.494199] PCI driver dc395x lacks driver specific resume support.
[ 11.494203] DC390: clustering now enabled by default. If you get problems load
[ 11.494205] with "disable_clustering=1" and report to maintainers
[ 11.494243] PCI driver tmscsim lacks driver specific resume support.
[ 11.494283] PCI driver megaraid_legacy lacks driver specific resume support.
[ 11.494288] megaraid cmm: 2.20.2.7 (Release Date: Sun Jul 16 00:01:03 EST 2006)
[ 11.494293] megaraid: 2.20.5.1 (Release Date: Thu Nov 16 15:32:35 EST 2006)
[ 11.494337] PCI driver megaraid lacks driver specific resume support.
[ 11.494340] megasas: 00.00.03.10-rc5 Thu May 17 10:09:32 PDT 2007
[ 11.494383] PCI driver megaraid_sas lacks driver specific resume support.
[ 11.494420] PCI driver atp870u lacks driver specific resume support.
[ 11.494424] GDT-HA: Storage RAID Controller Driver. Version: 3.05
[ 11.494603] GDT-HA: Found 0 PCI Storage RAID Controllers
[ 11.494644] PCI driver inia100 lacks driver specific resume support.
[ 11.494647] 3ware Storage Controller device driver for Linux v1.26.02.002.
[ 11.494680] PCI driver 3w-xxxx lacks driver specific resume support.
[ 11.494683] 3ware 9000 Storage Controller device driver for Linux v2.26.02.008.
[ 11.494718] PCI driver 3w-9xxx lacks driver specific resume support.
[ 11.494720] ipr: IBM Power RAID SCSI Device Driver version: 2.4.1 (April 24, 2007)
[ 11.494765] PCI driver ipr lacks driver specific resume support.
[ 11.494768] RocketRAID 3xxx SATA Controller driver v1.0 (060426)
[ 11.494892] PCI driver hptiop lacks driver specific resume support.
[ 11.494894] stex: Promise SuperTrak EX Driver version: 3.6.0000.1
[ 11.494926] PCI driver stex lacks driver specific resume support.
[ 11.494930] st: Version 20070203, fixed bufsize 32768, s/g segs 256
[ 11.494971] osst :I: Tape driver with OnStream support version 0.99.4
[ 11.494973] osst :I: $Id: osst.c,v 1.73 2005/01/01 21:13:34 wriede Exp $
[ 11.495153] PCI driver sata_svw lacks driver specific resume support.
[ 11.495225] PCI driver sata_promise lacks driver specific resume support.
[ 11.495258] PCI driver sata_qstor lacks driver specific resume support.
[ 11.495393] PCI driver sata_vsc lacks driver specific resume support.
[ 11.495429] PCI driver sata_sis lacks driver specific resume support.
[ 11.495462] PCI driver sata_sx4 lacks driver specific resume support.
[ 11.495539] sata_uli 0000:00:1f.1: version 1.2
[ 11.495565] ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 21 (level, low) -> IRQ 21
[ 11.495795] scsi0 : sata_uli
[ 11.495814] Device driver host0 lacks bus and class support for being resumed.
[ 11.495885] scsi1 : sata_uli
[ 11.495893] Device driver host1 lacks bus and class support for being resumed.
[ 11.495951] scsi2 : sata_uli
[ 11.495960] Device driver host2 lacks bus and class support for being resumed.
[ 11.496018] scsi3 : sata_uli
[ 11.496027] Device driver host3 lacks bus and class support for being resumed.
[ 11.496076] ata1: SATA max UDMA/133 cmd 0x000000000001e100 ctl 0x000000000001e112 bmdma 0x000000000001e140 irq 21
[ 11.496082] ata2: SATA max UDMA/133 cmd 0x000000000001e120 ctl 0x000000000001e132 bmdma 0x000000000001e148 irq 21
[ 11.496087] ata3: SATA max UDMA/133 cmd 0x000000000001e108 ctl 0x000000000001e116 bmdma 0x000000000001e150 irq 21
[ 11.496093] ata4: SATA max UDMA/133 cmd 0x000000000001e128 ctl 0x000000000001e136 bmdma 0x000000000001e158 irq 21
[ 11.798290] ata1: SATA link down (SStatus 0 SControl 300)
[ 12.100768] ata2: SATA link down (SStatus 0 SControl 300)
[ 12.554017] ata3: SATA link up <unknown> (SStatus 3 SControl 300)
[ 13.007254] ata4: SATA link up <unknown> (SStatus 3 SControl 300)
[ 13.007285] PCI driver sata_uli lacks driver specific resume support.
[ 13.007332] PCI driver sata_mv lacks driver specific resume support.
[ 13.007397] PCI driver pdc_adma lacks driver specific resume support.
[ 13.007457] ACPI: PCI Interrupt 0000:00:1f.0[A] -> GSI 21 (level, low) -> IRQ 21
[ 13.007578] scsi4 : pata_ali
[ 13.007588] Device driver host4 lacks bus and class support for being resumed.
[ 13.007643] scsi5 : pata_ali
[ 13.007652] Device driver host5 lacks bus and class support for being resumed.
[ 13.007697] ata5: PATA max UDMA/133 cmd 0x00000000000101f0 ctl 0x00000000000103f6 bmdma 0x0000000000011100 irq 14
[ 13.007701] ata6: PATA max UDMA/133 cmd 0x0000000000010170 ctl 0x0000000000010376 bmdma 0x0000000000011108 irq 15
[ 13.161609] ata5.00: ATA-6: IC25N080ATMR04-0, MO4OAD4A, max UDMA/100
[ 13.161613] ata5.00: 156301488 sectors, multi 16: LBA48
[ 13.161621] ata5.00: limited to UDMA/33 due to 40-wire cable
[ 13.167580] ata5.00: configured for UDMA/33
[ 13.471831] ata6.00: ATAPI: Slimtype DVDRW SOSW-833S, VRS3, max UDMA/33
[ 13.628578] ata6.00: configured for UDMA/33
[ 13.628594] Device driver target4:0:0 lacks bus and class support for being resumed.
[ 13.628684] scsi 4:0:0:0: Direct-Access ATA IC25N080ATMR04-0 MO4O PQ: 0 ANSI: 5
[ 13.628802] sd 4:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
[ 13.628815] sd 4:0:0:0: [sda] Write Protect is off
[ 13.628818] sd 4:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 13.628835] sd 4:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 13.628892] sd 4:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
[ 13.628902] sd 4:0:0:0: [sda] Write Protect is off
[ 13.628905] sd 4:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 13.628920] sd 4:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 13.628924] sda: sda1 sda2 < sda5 > sda3 sda4
[ 13.677499] sd 4:0:0:0: [sda] Attached SCSI disk
[ 13.677579] sd 4:0:0:0: Attached scsi generic sg0 type 0
[ 13.677608] Device driver target5:0:0 lacks bus and class support for being resumed.
[ 13.678180] scsi 5:0:0:0: CD-ROM Slimtype DVDRW SOSW-833S VRS3 PQ: 0 ANSI: 5
[ 13.682305] sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
[ 13.682308] Uniform CD-ROM driver Revision: 3.20
[ 13.682368] sr 5:0:0:0: Attached scsi CD-ROM sr0
[ 13.682431] sr 5:0:0:0: Attached scsi generic sg1 type 5
[ 13.682541] PCI driver pata_artop lacks driver specific resume support.
[ 13.682832] PCI driver pata_hpt37x lacks driver specific resume support.
[ 13.682869] PCI driver pata_hpt3x2n lacks driver specific resume support.
[ 13.683293] PCI driver pata_pdc2027x lacks driver specific resume support.
[ 13.683574] PCI driver pata_sl82c105 lacks driver specific resume support.
[ 13.683694] I2O subsystem v1.325
[ 13.683696] i2o: max drivers = 8
[ 13.683801] PCI driver PCI_I2O lacks driver specific resume support.
[ 13.683804] I2O Configuration OSM v1.323
[ 13.683877] I2O Bus Adapter OSM v1.317
[ 13.683906] I2O Block Device OSM v1.325
[ 13.683996] I2O SCSI Peripheral OSM v1.316
[ 13.684027] I2O ProcFS OSM v1.316
[ 13.684058] Fusion MPT base driver 3.04.04
[ 13.684060] Copyright (c) 1999-2007 LSI Logic Corporation
[ 13.684071] Fusion MPT SPI Host driver 3.04.04
[ 13.684132] Fusion MPT FC Host driver 3.04.04
[ 13.684184] Fusion MPT SAS Host driver 3.04.04
[ 13.684238] Fusion MPT misc device (ioctl) driver 3.04.04
[ 13.684280] mptctl: Registered with Fusion MPT base driver
[ 13.684283] mptctl: /dev/mptctl @ (major,minor=10,220)
[ 13.684285] Fusion MPT LAN driver 3.04.04
[ 13.684375] usbcore: registered new interface driver usblp
[ 13.684380] drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
[ 13.684383] Initializing USB Mass Storage driver...
[ 13.684417] usbcore: registered new interface driver usb-storage
[ 13.684420] USB Mass Storage support registered.
[ 13.684455] usbcore: registered new interface driver libusual
[ 13.684457] USB driver libusual lacks resume support.
[ 13.684540] PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 13.687426] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 13.687431] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 13.692712] parkbd: no such parport
[ 13.692836] PCI driver pcips2 lacks driver specific resume support.
[ 13.692960] mice: PS/2 mouse device common for all mice
[ 13.695625] input: AT Translated Set 2 keyboard as /class/input/input5
[ 14.238119] Synaptics Touchpad, model: 1, fw: 6.2, id: 0x3aa0b4, caps: 0xa04713/0x200000
[ 14.268658] input: SynPS/2 Synaptics TouchPad as /class/input/input6
[ 14.270931] md: linear personality registered for level -1
[ 14.270934] md: raid0 personality registered for level 0
[ 14.270937] md: raid1 personality registered for level 1
[ 14.270939] md: raid10 personality registered for level 10
[ 14.287092] raid6: int64x1 1660 MB/s
[ 14.304072] raid6: int64x2 2121 MB/s
[ 14.321036] raid6: int64x4 2031 MB/s
[ 14.338002] raid6: int64x8 1464 MB/s
[ 14.354984] raid6: sse2x1 2234 MB/s
[ 14.371953] raid6: sse2x2 2992 MB/s
[ 14.388921] raid6: sse2x4 3218 MB/s
[ 14.388923] raid6: using algorithm sse2x4 (3218 MB/s)
[ 14.388926] md: raid6 personality registered for level 6
[ 14.388929] md: raid5 personality registered for level 5
[ 14.388931] md: raid4 personality registered for level 4
[ 14.388934] raid5: automatically using best checksumming function: generic_sse
[ 14.393902] generic_sse: 5500.000 MB/sec
[ 14.393904] raid5: using function: generic_sse (5500.000 MB/sec)
[ 14.393907] md: multipath personality registered for level -4
[ 14.393910] md: faulty personality registered for level -5
[ 14.394002] device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
[ 14.394149] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2)
[ 14.394188] usbcore: registered new interface driver hiddev
[ 14.394191] USB driver hiddev lacks resume support.
[ 14.394221] usbcore: registered new interface driver usbhid
[ 14.394224] drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
[ 14.394264] Advanced Linux Sound Architecture Driver Version 1.0.14 (Thu May 31 09:03:25 2007 UTC).
[ 14.394314] ALSA device list:
[ 14.394316] No soundcards found.
[ 14.394390] TCP bic registered
[ 14.394399] NET: Registered protocol family 1
[ 14.394403] NET: Registered protocol family 17
[ 14.394483] powernow-k8: Found 1 AMD Turion(tm) 64 Mobile Technology ML-32 processors (version 2.00.00)
[ 14.394527] powernow-k8: 0 : fid 0xa (1800 MHz), vid 0x4
[ 14.394530] powernow-k8: 1 : fid 0x8 (1600 MHz), vid 0x6
[ 14.394533] powernow-k8: 2 : fid 0x0 (800 MHz), vid 0x16
[ 14.394589] Suspend v2.2.10
[ 14.394641] Suspend2 Checksumming support registered.
[ 14.394671] Suspend2 Userspace Storage Manager support registered.
[ 14.394702] Suspend2 Basic User Interface support registered.
[ 14.394731] Suspend2 Compressor support registered.
[ 14.394761] Suspend2 Block I/O support registered.
[ 14.394793] Suspend2 Swap Allocator support registered.
[ 14.394825] Suspend2 File Allocator support registered.
[ 14.394831] Suspend2 Userspace UI support registered.
[ 14.395032] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 14.395041] Freeing unused kernel memory: 396k freed
[ 14.541891] ata1: exception Emask 0x2 SAct 0x0 SErr 0x800400 action 0x2
[ 14.844154] ata1: soft resetting port
[ 14.844163] ata1: SATA link down (SStatus 0 SControl 300)
[ 14.844187] ata1: EH complete
[ 14.989398] PCI: Enabling device 0000:00:1c.3 (0000 -> 0002)
[ 14.989411] ACPI: PCI Interrupt 0000:00:1c.3[D] -> GSI 23 (level, low) -> IRQ 23
[ 14.989521] ehci_hcd 0000:00:1c.3: EHCI Host Controller
[ 14.989681] ehci_hcd 0000:00:1c.3: new USB bus registered, assigned bus number 1
[ 14.989742] ehci_hcd 0000:00:1c.3: debug port 1
[ 15.009885] ehci_hcd 0000:00:1c.3: irq 23, io mem 0x48003000
[ 15.009894] ehci_hcd 0000:00:1c.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 15.010046] Device driver usbdev1.1_ep00 lacks bus and class support for being resumed.
[ 15.010055] usb usb1: configuration #1 chosen from 1 choice
[ 15.010103] hub 1-0:1.0: USB hub found
[ 15.010115] hub 1-0:1.0: 8 ports detected
[ 15.110760] Device driver usbdev1.1_ep81 lacks bus and class support for being resumed.
[ 15.142272] USB Universal Host Controller Interface driver v3.0
[ 15.223557] sl811: driver sl811-hcd, 19 May 2005
[ 15.343323] usb 1-3: new high speed USB device using ehci_hcd and address 2
[ 15.352986] Intel(R) PRO/1000 Network Driver - version 7.3.20-k2
[ 15.352991] Copyright (c) 1999-2006 Intel Corporation.
[ 15.458145] Device driver usbdev1.2_ep00 lacks bus and class support for being resumed.
[ 15.458157] usb 1-3: configuration #1 chosen from 1 choice
[ 15.458458] Device driver usbdev1.2_ep01 lacks bus and class support for being resumed.
[ 15.458500] Device driver usbdev1.2_ep82 lacks bus and class support for being resumed.
[ 15.458545] Device driver usbdev1.2_ep83 lacks bus and class support for being resumed.
[ 15.458590] Device driver usbdev1.2_ep04 lacks bus and class support for being resumed.
[ 16.710322] No storage allocator is currently active. Rechecking whether we can use one.
[ 16.732012] Suspend2: SwapAllocator: Signature found.
[ 16.732016] Suspend2: Resuming enabled.
[ 16.738058] Suspend2: Failed to initialise the lzf compression transform.
[ 16.738339] Suspend2: Normal swapspace found.
[ 16.768663] EXT3-fs: INFO: recovery required on readonly filesystem.
[ 16.768668] EXT3-fs: write access will be enabled during recovery.
[ 18.615122] kjournald starting. Commit interval 5 seconds
[ 18.615139] EXT3-fs: recovery complete.
[ 18.615900] EXT3-fs: mounted filesystem with ordered data mode.
[ 23.670361] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 23.760295] PCI driver shpchp lacks driver specific resume support.
[ 23.760299] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 24.186062] Yenta: CardBus bridge found at 0000:00:10.0 [1631:c00a]
[ 24.186086] Yenta: Enabling burst memory read transactions
[ 24.186091] Yenta: Using CSCINT to route CSC interrupts to PCI
[ 24.186094] Yenta: Routing CardBus interrupts to PCI
[ 24.186100] Yenta TI: socket 0000:00:10.0, mfunc 0x01ac1b22, devctl 0x66
[ 24.339624] uli526x: ULi M5261/M5263 net driver, version 0.9.3 (2005-7-29)
[ 24.372560] input: PC Speaker as /class/input/input7
[ 24.388140] sdhci: Secure Digital Host Controller Interface driver
[ 24.388145] sdhci: Copyright(c) Pierre Ossman
[ 24.408837] Yenta: ISA IRQ mask 0x0cf8, PCI irq 17
[ 24.408843] Socket status: 30000006
[ 24.428617] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
[ 24.660665] Device driver pcmcia_socket0 lacks bus and class support for being resumed.
[ 24.661669] ACPI: PCI Interrupt 0000:00:10.3[A] -> GSI 17 (level, low) -> IRQ 17
[ 24.662106] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 20 (level, low) -> IRQ 20
[ 24.732831] Device driver eth0 lacks bus and class support for being resumed.
[ 24.732865] eth0: ULi M5263 at pci0000:00:1b.0, 00:40:d0:7f:b1:a0, irq 20.
[ 24.733080] PCI driver k8temp lacks driver specific resume support.
[ 24.733097] sdhci: SDHCI controller found at 0000:00:10.4 [104c:8034] (rev 0)
[ 24.733118] ACPI: PCI Interrupt 0000:00:10.4[A] -> GSI 17 (level, low) -> IRQ 17
[ 24.733565] Device driver mmc0 lacks bus and class support for being resumed.
[ 24.733580] mmc0: SDHCI at 0xd000a000 irq 17 DMA
[ 24.733747] Device driver mmc1 lacks bus and class support for being resumed.
[ 24.733760] mmc1: SDHCI at 0xd000a100 irq 17 DMA
[ 24.733905] Device driver mmc2 lacks bus and class support for being resumed.
[ 24.733917] mmc2: SDHCI at 0xd000a200 irq 17 DMA
[ 24.733973] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 24.734056] ohci_hcd 0000:00:1c.0: OHCI Host Controller
[ 24.734127] ohci_hcd 0000:00:1c.0: new USB bus registered, assigned bus number 2
[ 24.734150] ohci_hcd 0000:00:1c.0: irq 17, io mem 0xf8002000
[ 24.740678] fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel.
[ 24.762576] ieee80211_crypt: registered algorithm 'NULL'
[ 24.765808] [fglrx] Maximum main memory to use for locked dma buffers: 793 MBytes.
[ 24.765829] [fglrx] module loaded - fglrx 8.38.6 [Jun 22 2007] on minor 0
[ 24.766747] ieee80211: 802.11 data/management/control stack, git-1.1.13
[ 24.766752] ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
[ 24.813825] Device driver usbdev2.1_ep00 lacks bus and class support for being resumed.
[ 24.813839] usb usb2: configuration #1 chosen from 1 choice
[ 24.814009] hub 2-0:1.0: USB hub found
[ 24.814030] hub 2-0:1.0: 3 ports detected
[ 24.914393] Device driver usbdev2.1_ep81 lacks bus and class support for being resumed.
[ 24.914634] ACPI: PCI Interrupt 0000:00:1d.0[C] -> GSI 22 (level, low) -> IRQ 22
[ 24.953168] usb 1-3: reset high speed USB device using ehci_hcd and address 2
[ 24.961151] hda_codec: Unknown model for ALC880, trying auto-probe from BIOS...
[ 25.056124] PCI: Enabling device 0000:00:11.0 (0000 -> 0002)
[ 25.056133] ACPI: PCI Interrupt 0000:00:11.0[A] -> GSI 19 (level, low) -> IRQ 19
[ 25.056143] PCI: Setting latency timer of device 0000:00:11.0 to 64
[ 25.075184] Device driver phy0 lacks bus and class support for being resumed.
[ 25.075452] Device driver wmaster0 lacks bus and class support for being resumed.
[ 25.089543] Device driver usbdev1.2_ep01 lacks bus and class support for being resumed.
[ 25.089768] Device driver usbdev1.2_ep82 lacks bus and class support for being resumed.
[ 25.090002] Device driver usbdev1.2_ep83 lacks bus and class support for being resumed.
[ 25.090228] Device driver usbdev1.2_ep04 lacks bus and class support for being resumed.
[ 25.090431] Device driver 1-3 lacks bus and class support for being resumed.
[ 25.263013] wmaster0: Selected rate control algorithm 'simple'
[ 25.271538] Device driver 1-3 lacks bus and class support for being resumed.
[ 25.288313] Device driver wlan0 lacks bus and class support for being resumed.
[ 25.288389] ali15x3_smbus 0000:00:1e.1: ALI15X3_smb region uninitialized - upgrade BIOS or use force_addr=0xaddr
[ 25.288395] ali15x3_smbus 0000:00:1e.1: ALI15X3 not detected, module not inserted.
[ 25.288413] PCI driver ali15x3_smbus lacks driver specific resume support.
[ 25.289599] PCI driver uli526x lacks driver specific resume support.
[ 25.291414] ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 18 (level, low) -> IRQ 18
[ 25.291563] ohci_hcd 0000:00:1c.1: OHCI Host Controller
[ 25.293471] ohci_hcd 0000:00:1c.1: new USB bus registered, assigned bus number 3
[ 25.293506] ohci_hcd 0000:00:1c.1: irq 18, io mem 0xf8003000
[ 25.304770] Device driver usbdev1.2_ep01 lacks bus and class support for being resumed.
[ 25.304797] Device driver usbdev1.2_ep82 lacks bus and class support for being resumed.
[ 25.304822] Device driver usbdev1.2_ep83 lacks bus and class support for being resumed.
[ 25.304848] Device driver usbdev1.2_ep04 lacks bus and class support for being resumed.
[ 25.353412] Device driver usbdev3.1_ep00 lacks bus and class support for being resumed.
[ 25.353426] usb usb3: configuration #1 chosen from 1 choice
[ 25.353460] hub 3-0:1.0: USB hub found
[ 25.354610] hub 3-0:1.0: 3 ports detected
[ 25.362393] zd1211rw 1-3:1.0: firmware version 4605
[ 25.404341] zd1211rw 1-3:1.0: zd1211 chip 0ace:1211 v4330 high 00-02-e3 RF2959_RF pa0 g----
[ 25.407102] Device driver eth1 lacks bus and class support for being resumed.
[ 25.407134] zd1211rw 1-3:1.0: eth1
[ 25.407154] usbcore: registered new interface driver zd1211rw
[ 25.407158] USB driver zd1211rw lacks resume support.
[ 25.415048] usbcore: registered new interface driver zd1211rw_mac80211
[ 25.415054] USB driver zd1211rw_mac80211 lacks resume support.
[ 25.455727] Device driver usbdev3.1_ep81 lacks bus and class support for being resumed.
[ 25.455994] ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 19 (level, low) -> IRQ 19
[ 25.456108] ohci_hcd 0000:00:1c.2: OHCI Host Controller
[ 25.456517] ohci_hcd 0000:00:1c.2: new USB bus registered, assigned bus number 4
[ 25.456537] ohci_hcd 0000:00:1c.2: irq 19, io mem 0xf8004000
[ 25.509768] Device driver usbdev4.1_ep00 lacks bus and class support for being resumed.
[ 25.509783] usb usb4: configuration #1 chosen from 1 choice
[ 25.510002] hub 4-0:1.0: USB hub found
[ 25.510020] hub 4-0:1.0: 3 ports detected
[ 25.610271] Device driver usbdev4.1_ep81 lacks bus and class support for being resumed.
[ 25.614261] ali1535_smbus 0000:00:1e.1: ALI1535_smb region uninitialized - upgrade BIOS?
[ 25.614266] ali1535_smbus 0000:00:1e.1: ALI1535 not detected, module not inserted.
[ 25.614284] PCI driver ali1535_smbus lacks driver specific resume support.
[ 25.674576] alim7101_wdt: Steve Hill <steve@navaho.co.uk>.
[ 25.675661] alim7101_wdt: ALi 1543 South-Bridge not present - WDT not set
[ 29.975400] EXT3 FS on dm-0, internal journal
[ 30.301123] vboxdrv: Trying to deactivate NMI watchdog permanently...
[ 30.301129] vboxdrv: Successfully done.
[ 30.978234] kjournald starting. Commit interval 5 seconds
[ 30.978461] EXT3 FS on sda1, internal journal
[ 30.978466] EXT3-fs: mounted filesystem with ordered data mode.
[ 31.071365] Adding 1802232k swap on /dev/VolGroup00/LogVol01. Priority:-1 extents:1 across:1802232k
[ 48.714238] fbsplash: console 1 using theme 'sabayon'
[ 48.721473] fbsplash: switched splash state to 'on' on console 1
[ 48.736567] fbsplash: console 2 using theme 'sabayon'
[ 48.749047] fbsplash: switched splash state to 'on' on console 2
[ 48.765712] fbsplash: console 3 using theme 'sabayon'
[ 48.772729] fbsplash: switched splash state to 'on' on console 3
[ 48.789338] fbsplash: console 4 using theme 'sabayon'
[ 48.798308] fbsplash: switched splash state to 'on' on console 4
[ 48.815111] fbsplash: console 5 using theme 'sabayon'
[ 48.823897] fbsplash: switched splash state to 'on' on console 5
[ 48.838266] fbsplash: console 11 using theme 'sabayon'
[ 48.847254] fbsplash: switched splash state to 'on' on console 11
[ 51.901546] ACPI: PCI Interrupt 0000:01:05.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 55.950212] [fglrx] total GART = 130023424
[ 55.950221] [fglrx] free GART = 114032640
[ 55.950225] [fglrx] max single GART = 114032640
[ 55.950228] [fglrx] total LFB = 134217728
[ 55.950231] [fglrx] free LFB = 116002816
[ 55.950235] [fglrx] max single LFB = 116002816
[ 55.950238] [fglrx] total Inv = 0
[ 55.950240] [fglrx] free Inv = 0
[ 55.950243] [fglrx] max single Inv = 0
[ 55.950245] [fglrx] total TIM = 0
[ 62.946077] uli526x: eth0 NIC Link is Down
[ 65.493037] atkbd.c: Spurious ACK on isa0060/serio0. Some program might be trying access hardware directly.
[ 66.493392] atkbd.c: Spurious ACK on isa0060/serio0. Some program might be trying access hardware directly.
[ 66.494461] psmouse.c: TouchPad at isa0060/serio1/input0 lost synchronization, throwing 5 bytes away.
[ 130.887769] ieee80211_crypt: registered algorithm 'WEP'
[ 130.909130] SoftMAC: Open Authentication completed with 00:03:c9:e6:2a:f8
[ 187.637603] scim-launcher[9730]: segfault at 0000000000000000 rip 0000000000000000 rsp 00007fffcfb91158 error 14
[ 188.690902] atkbd.c: Spurious ACK on isa0060/serio0. Some program might be trying access hardware directly.
[ 189.691191] atkbd.c: Spurious ACK on isa0060/serio0. Some program might be trying access hardware directly.
[ 213.432388] SoftMAC: Open Authentication completed with 00:03:c9:e6:2a:f8
[ 229.493465] SoftMAC: Open Authentication completed with 00:03:c9:e6:2a:f8
localhost federoco #

----

Sorry for my english and for my newbieness.